Atosa Mixrite ST3660EC Stainless Steel Work Table 36 x 60, Flat Top, Undershelf, NSF

The Atosa Mixrite ST3660EC is a 60" wide, 36" deep stainless steel work table with a flat top and an adjustable undershelf. It stands 34" high. It is built from 18 gauge, 430 stainless steel. It is NSF listed and ships knocked down.

Key Specs at a Glance

The 36 x 60 Size

At 60" x 36", the ST3660EC is a large, deep table for open floor space. It can serve as a center prep table that staff work from both sides, with room for sheet pans, tubs and boards at the same time.

The top gives you 2,160 square inches of work surface, about 15 square feet. Before you order, measure the space: you need 60" of width, and the table comes 36" out from the wall. Check how much aisle space is left behind anyone standing at the table.

Choosing the Depth

A 36" deep table gives you the most room front to back. It suits large batches, full sheet pans laid out side by side, and tables that people work from both sides. Make sure you have the floor space: it comes 12" further into the room than a 24" deep table.

The Flat Top

The top is flat edge to edge, with no backsplash or raised rear edge. That makes it the right choice when the table stands away from a wall, sits in an open area, or gets worked from more than one side. You can slide pans, boards and boxes on and off from any edge.

Atosa polishes the whole top to a satin finish and sound deadens it, which reduces the ringing noise of tools and pans set down on bare steel. All edges are turned down, so there is no sharp cut edge where staff lean or reach.

Height and Clearance

The work surface is 34" high. If the table will slide under a shelf or counter overhang, measure that clearance first.

The Undershelf

The undershelf is stainless steel and adjusts in height. Use it for bins, bowls, sheet pans and boxed product. Measure your tallest item before you set the height: a lower shelf gives more clearance, a higher shelf keeps items closer to hand.

Load Ratings

The Atosa listing for this model does not include a weight rating. Spread heavy items out and keep the heaviest near the legs.

For heavy countertop cooking equipment, use an equipment stand instead. The SE3660ECR2 is 60-1/4" wide and 36" deep.

Legs and Leveling

The ST3660EC stands on 4 stainless steel tubular legs, 1-5/8" in diameter, with 1" adjustable bullet feet. Use the feet to level it on an uneven floor so it does not rock.

Compare Nearby Sizes

Here is how the ST3660EC compares with the other 36" deep flat top tables:

• Smaller: ST3648EC, 48" wide.
• Larger: ST3672EC, 72" wide.
• Same width at 24" deep: ST2460EC (saves floor space).
• Same width at 30" deep: ST3060EC (saves floor space).

Assembly

The ST3660EC ships knocked down (KD), and Atosa says it is easy to assemble. The shipping weight is 85.31 lb. Put it together near where it will stand, then level it with the feet.

Before You Order

• Measure the space: 60" wide and 36" deep.
• Check the aisle space left behind the table.
• Decide whether you need a flat top or a raised back for a wall.

Frequently Asked Questions

What size is the Atosa ST3660EC?

60" wide, 36" deep and 34" high.

What is it made of?

18 gauge, 430 stainless steel, including the top, undershelf and legs.

Is the undershelf adjustable?

Yes.

Does it come assembled?

No. It ships knocked down. Atosa says it is easy to assemble.

Is it NSF listed?

Yes. The Atosa spec sheet shows the NSF mark.

What is the warranty?

90 days on workmanship.